Home › Insurance claims › Remediator vs. general contractor
Insurance guide · Choosing the right contractor
Certified mold remediator vs. general contractor: who should handle your claim?
Short answer: Use a trained restoration and remediation company for the mitigation phase — water extraction, structural drying, containment and mold removal — and a general contractor (or the same company, if they offer it) for the rebuild afterward. Rebuilding before the structure is verified dry and clean traps moisture and mold behind new walls, and most carriers will not pay to do the job twice.
Mitigate first, rebuild second
Different tools, different training
Carriers pay these as separate line items
Clearance testing before drywall
Two different jobs that look similar from the outside
Both trades show up with trucks and cut drywall, so homeowners often assume they are interchangeable. They are not. A general contractor’s job is to put a house back together: framing, drywall, trim, paint, flooring. A restoration company’s job is to stop the damage from getting worse and make the structure safe to rebuild: extracting water, measuring moisture inside materials, drying framing and subfloor with commercial dehumidifiers and air movers, building negative-pressure containment, removing contaminated material and cleaning what remains.
The equipment is different (a general contractor rarely owns a thermal camera, pin and non-invasive moisture meters, LGR dehumidifiers or HEPA air scrubbers), the training is different (IICRC S500 and S520 rather than building codes), and the paperwork is different (drying logs and moisture maps rather than permits and plans).
What goes wrong when a GC does the mitigation
The most common failure we are called in to fix is a basement or bathroom that was rebuilt too soon. A contractor pulled the wet drywall, ran a box fan for a weekend, and hung new drywall. Six weeks later the homeowner smells it. Moisture readings in the bottom plate and studs were never taken, so the framing was still at 25–30% moisture content when it was sealed up — well above the 15–16% that counts as dry — and mold did what mold does.
The second failure is cross-contamination. Mold removal without containment and negative air spreads spores through the HVAC system to rooms that were never affected. The remediation standard, S520, exists largely to prevent this, and it is why we build plastic containment with HEPA-filtered negative air before disturbing anything.
The third is the claim itself. Insurance carriers pay mitigation and rebuild as separate scopes. If there is no drying documentation, the adjuster has no basis to approve the mitigation invoice, and if mold later appears, the carrier can argue the loss was not properly mitigated — which is grounds to deny the second claim.
The right sequence
How a water or mold loss should flow
✔ Day 0: emergency response — stop the source, extract standing water, document everything with photos and a moisture map.
✔ Days 1–4: structural drying with dehumidifiers and air movers, daily moisture readings logged for the adjuster.
✔ If mold is present: containment, negative air, removal of affected material, HEPA vacuuming and antimicrobial treatment to S520.
✔ Clearance: an independent inspector confirms the area is dry and clean (post-remediation verification).
✔ Only then: rebuild — insulation, drywall, trim, paint, flooring — by a general contractor or a restoration company that offers reconstruction.
Can one company do both?
Yes, and it is often simpler for the homeowner. Many restoration companies, including ours, handle both the mitigation and the rebuild so you are not coordinating two crews and two invoices with the adjuster. The important thing is that the two phases stay separate in practice: the rebuild does not start until the drying report and clearance are in hand, and the carrier receives them as separate scopes.
If you already have a general contractor you trust for the rebuild, that works too. We will hand over a complete dry-out file so they can start on a verified-dry structure.
Where we stand: Certified Restoration Services is a restoration and remediation company first. Our technicians are IICRC-trained and we follow IICRC S500 and S520 on every job. We also offer the rebuild once drying and clearance are documented, or we will coordinate with your contractor.
Related
Keep reading
What certifications to require
Insurance, registration, standards and documentation — what to ask for and why.
Mold remediation
How we contain, remove and verify mold in Bucks, Montgomery, Delaware and Philadelphia homes.
Questions
Homeowners ask
My contractor says he can handle the mold himself. Should I let him?
Only if he can show you S520-based procedures: containment, negative air with HEPA filtration, and an independent clearance test afterward. If the plan is to spray it and paint over it, no — that is how mold comes back and how claims get denied.
Will my insurance pay for a remediation company and a contractor?
Typically yes. Mitigation and rebuild are separate scopes on a claim, each with its own estimate. Your adjuster expects to see both.
How do I know the structure is actually dry?
Ask for the final drying report. It should show moisture readings for every affected material back at or near the readings of unaffected material in the same house (the dry standard), not just that the equipment ran for a set number of days.
Do you rebuild after you dry and remediate?
Yes. We can handle drywall, insulation, trim, paint and flooring after the drying report and clearance are complete, or hand the file to your own contractor.
Not sure what phase you are in?
Send us photos or call and we will tell you whether you need mitigation, remediation, rebuild — or all three.
